automatic chuck extractor - translation to ρωσικά
Diclib.com
Λεξικό ChatGPT
Εισάγετε μια λέξη ή φράση σε οποιαδήποτε γλώσσα 👆
Γλώσσα:

Μετάφραση και ανάλυση λέξεων από την τεχνητή νοημοσύνη ChatGPT

Σε αυτήν τη σελίδα μπορείτε να λάβετε μια λεπτομερή ανάλυση μιας λέξης ή μιας φράσης, η οποία δημιουργήθηκε χρησιμοποιώντας το ChatGPT, την καλύτερη τεχνολογία τεχνητής νοημοσύνης μέχρι σήμερα:

  • πώς χρησιμοποιείται η λέξη
  • συχνότητα χρήσης
  • χρησιμοποιείται πιο συχνά στον προφορικό ή γραπτό λόγο
  • επιλογές μετάφρασης λέξεων
  • παραδείγματα χρήσης (πολλές φράσεις με μετάφραση)
  • ετυμολογία

automatic chuck extractor - translation to ρωσικά

DEVICE USED IN GUNS OF ARMORED FIGHTING VEHICLES
Fume extractor
  • Bore evacuator on an [[M1 Abrams]]

automatic chuck extractor      

нефтегазовая промышленность

автоматический механический домкрат патронного типа для бурильных труб (применяется в лёгкой буровой установке)

three-jaw chuck         
  • Arthur Irving Jacobs (1858–1918)
  • drill shanks]] of a range of diameters. The end view shows the three small jaws that slide within the body.
  • Independent four-jaw chuck, with the jaws independently set. The key is used to adjust each jaw separately.
  • The Jacobs type chuck, with three converging splines or jaws, is perhaps the most usual design. This one is tightened with a key, but some types may be sufficiently tightened by hand
  • Chuck with six jaws
  • faceplate]]. The jaws are stepped on one side and full height for gripping on the other and are reversible.  Generally the jaws are usable for holding either outside as shown here, or inside as in gripping the inside of a pipe.
  • Two pin chucks. The top one is assembled, the lower one shows the body and nose cap assembled with the collet piece below it.
  • Diagram of an SDS chuck
  • Taper spindle nose with threaded retention. The retainer ring is wrenched with a spanner wrench.
  • Self-centering three-jaw chuck and key with one jaw removed and inverted showing the teeth that engage in the scroll plate. The scroll plate is rotated within the chuck body by the key, the scroll engages the teeth on the underside of the jaws which moves the three jaws in unison, to tighten or release the workpiece.
SPECIALIZED TYPE OF CLAMP TO HOLD A ROTATING TOOL OR WORKPIECE
Pin chuck; Four-jaw chuck; Three-jaw chuck; Scroll chuck; Independent-jaw chuck; Arthur I. Jacobs; Lathe chuck; Chuck key; Drill chuck; Tool chuck; Scroll plate; Self-centering chuck; Scroll gear; Special Direct System

нефтегазовая промышленность

трёхкулачковый патрон

патрон с тремя плашками

lathe chuck         
  • Arthur Irving Jacobs (1858–1918)
  • drill shanks]] of a range of diameters. The end view shows the three small jaws that slide within the body.
  • Independent four-jaw chuck, with the jaws independently set. The key is used to adjust each jaw separately.
  • The Jacobs type chuck, with three converging splines or jaws, is perhaps the most usual design. This one is tightened with a key, but some types may be sufficiently tightened by hand
  • Chuck with six jaws
  • faceplate]]. The jaws are stepped on one side and full height for gripping on the other and are reversible.  Generally the jaws are usable for holding either outside as shown here, or inside as in gripping the inside of a pipe.
  • Two pin chucks. The top one is assembled, the lower one shows the body and nose cap assembled with the collet piece below it.
  • Diagram of an SDS chuck
  • Taper spindle nose with threaded retention. The retainer ring is wrenched with a spanner wrench.
  • Self-centering three-jaw chuck and key with one jaw removed and inverted showing the teeth that engage in the scroll plate. The scroll plate is rotated within the chuck body by the key, the scroll engages the teeth on the underside of the jaws which moves the three jaws in unison, to tighten or release the workpiece.
SPECIALIZED TYPE OF CLAMP TO HOLD A ROTATING TOOL OR WORKPIECE
Pin chuck; Four-jaw chuck; Three-jaw chuck; Scroll chuck; Independent-jaw chuck; Arthur I. Jacobs; Lathe chuck; Chuck key; Drill chuck; Tool chuck; Scroll plate; Self-centering chuck; Scroll gear; Special Direct System

медицина

насадка для шлифмашины

Ορισμός

АРУЗ
(аруд) (араб.), система метрического стихосложения, возникшая в классической арабской поэзии и распространенная (вплоть до 20 в.) в ряде стран Ближнего и Ср. Востока. Ритмообразующий элемент стиха в арузе - варьирующееся чередование долгих и кратких слогов.

Βικιπαίδεια

Bore evacuator

A bore evacuator or fume extractor is a device which removes lingering gases and airborne residues from the barrel of an armored fighting vehicle's gun after firing, particularly in tanks and self-propelled guns. By creating a pressure differential in the barrel after the shell leaves, the bore evacuator causes most of the propellant gases and combustion residues to exit via the muzzle. Thus, when the breech opens for reloading, those gases and residues do not escape into the crew compartment and pose a hazard to the gun crew.

Μετάφραση του &#39automatic chuck extractor&#39 σε Ρωσικά